Vista Ademco -10SE User's Guide download pdf (Page 14)

– 14 –

Trouble Conditions

"Check" and

"Battery" Displays

* Not all systems

use wireless

sensors.

The word CHECK on the keypad's display, accompanied by a "beeping" at the keypad, indicates a

trouble condition in the system.

To silence the beeping for these conditions, press any key.

• "CHECK" and one or more zone numbers indicates that a problem exists with the displayed zone(s)

and requires your attention. Determine if the zone(s) displayed are intact and make them so if they

are not. If the problem has been corrected, the display can be cleared if you enter the OFF sequence

(security code plus OFF key) twice. If the display persists, CALL FOR SERVICE.

NOTE: CHECK

70 on Fixed-Word/Icon Display keypads indicates that the wiring connection

to the external sounder is faulted (opened or shorted), and you should CALL FOR SERVICE. See

“BELL FAILURE” on next page. A display of CHECK 90 indicates that RF interference may be

preventing the operation of wireless sensors* in the system. See “Rcvr Jam” on next page.

• If there are wireless sensors* in your system, the CHECK condition may also be caused by some

change in the environment that prevents the wireless receiver from receiving communication from a

particular sensor. CALL FOR SERVICE if this occurs.

Other Trouble Displays

Words or letters in parentheses

( ) are those that are

displayed on Fixed-Word/Icon

Display keypads.

* Any “beeping” that

accompanies a trouble

display can be stopped by

depressing any key on

the keypad or by

entering an OFF

sequence (code + OFF)

** Not all systems use

wireless sensors.

COMM. FAILURE Indicates that a failure has occurred in the telephone communication

(or FC) portion of your system. CALL FOR SERVICE.

SYSTEM LO BAT Indicates that a low system battery condition exists. Display is

(or BAT

with no accompanied by "beeping"* at the keypad. Depending on installer

zone No.) programming, a system low battery may prevent arming, or you may

need to perform the arming sequence twice to override the condition

(see your installer). If this condition persists for more than one day

(with AC present), CALL FOR SERVICE.

Tamper If programmed, indicates a tamper fault condition (e.g. cover removed)

+ 1 + device number exists at the device shown.

LO BAT Indicates that there is a low battery condition in the wireless

+ zone descriptor transmitter** number displayed (00 is RF keypad).

(or BAT

with Accompanied by a single "beep"

(once every 40 seconds) at the keypad.

zone No.) Either replace the battery yourself, or CALL FOR SERVICE. If the

battery is not replaced within 30 days, a CHECK display may occur

indicating that the transmitter is no longer operating.

Rcvr Jam Wireless part of the system is experiencing

(or CHECK

90) RF interference which may prevent reception from wireless sensors.**

MODEM COMM Indicates that the control is on-line with the Central

(or CC) Monitoring Station's or your installer’s remote computer.

The control will not operate while on-line. Wait a few minutes — the

display should disappear.

BELL FAILURE Indicates that the wiring connection to the external sounder

(or CHECK 70) is at fault (open or shorted). Accompanied by “beeping” at the keypad.

CALL FOR SERVICE.

AC LOSS The system is only operating on battery power due to an AC power

(or NO AC

) failure. If only some lights are out on the premises, check circuit

breakers and fuses and reset or replace as necessary. Depending on

installer programming, an AC loss may prevent arming, or you may

need to perform the arming sequence twice to override the condition

(see your installer).

If AC power cannot be restored and a “low system battery” message

appears, CALL FOR SERVICE.

Busy-Standby

(or dI)

If this message remains displayed for more than 1 minute, system is

disabled. CALL FOR SERVICE.

OPEN CIRCUIT The keypad is not receiving signals from the control. CALL FOR

(or OC) SERVICE.

Long Rng Trbl If installed, the back-up communications media portion of your

(or bF) system has failed (e.g. internet, intranet networks, long range radio).

CALL FOR SERVICE.

TELCO FAULT The telephone line has a problem.

(or CHECK 94) CALL FOR SERVICE.

Total Power Failure

If there is no keypad display at all, and the READY indicator is not lit, operating power (from AC and bac

up battery) for the system has stopped and the system is inoperative. CALL FOR SERVICE.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 23 24

Comments to this Manuals

No comments

Vista Ademco -10SE User's Guide Page 14

Comments to this Manuals

Related products and manuals for Security access control systems Vista Ademco -10SE