Vista Ademco -10SE User's Guide download pdf (Page 11)

– 11 –

Time and Date Functions

Viewing the

Time and Date

• Master Code+[#] + [6] [3], or if programmed, press the designated function key.

• The system lets you view its time and date setting.

• The display remains on for about 30 seconds.

To Set the

Time and Date

• Master Code+[#] + [6] [3], then press [∗] while the time/date is displayed.

• A cursor appears under the first digit of the hour.

NOTE: To move cursor ahead, press [∗]. To go back, press [#].

• Enter the 2-digit hour setting; enter the 2-digit minute setting.

• Enter the last two digits of the current year.

• Enter the 2-digit month setting (01-12); enter the 2-digit day setting (01-31).

• Press [∗] to accept the settings and continue.

The Clock Adjustment prompt is displayed. This prompt lets you add or subtract up to 59 seconds per

day, if needed, to keep the real-time clock accurate.

• Press [0] to add seconds per day, or press [1] to subtract seconds per day.

• Enter the desired number of seconds per day (01-59) to add or subtract.

• Press [∗] to accept the settings and exit. This mode automatically exits after 10 seconds.

Event Log

The system records up to 254 events in a history log, which can be viewed by the master user using an Alpha Display keypad.

To view the • Master Code+ [#] + [6] [0]

Event Log • The system displays the most recent event as follows:

001 E441 U001 P1 Pressing [∗] displays previous events (back in time).

13:38 21/06/02 Pressing [#] displays events forward in time.

event number, type of event, identified by its corresponding code, displayed in chronological order, from

most recent to oldest.

zone or user number (depending on type of event), partition in which event occurred,

time and date of the event’s occurrence.

• When the log is full, the oldest event is replaced by the logging of any new event.

• Refer to the Event Log Codes Table below for the meanings of the various codes.

Exit Event Log • Press any key other than [∗] or [#]

Event Log Codes Table

Code Definition

110 Fire Alarm

121 Duress

122 Alarm, 24-hour Silent

123 Alarm, 24-hour Audible

131 Alarm, Perimeter

132 Alarm, Interior

134 Alarm, Entry/Exit

135 Alarm, Zone Type 5

143 Alarm, Expansion Module

144 Sensor Tamper Alarm

145 ECP Module Cover Tamper Alarm

146 Silent Burglary Alarm

150 Alarm, 24-Hour Auxiliary/Monitor zone

162 Gas Alarm

301 AC Power

302 Low System Battery/Battery Test Fail

305 System Reset (Log only)

321 Siren Supervision Failure

333 Trouble, Expansion Mod. Supervision

341 Trouble, ECP Cover Tamper

344 RF Receiver Jam

351 Telecom Line Fault

353 Alternative Comm. Media Trouble

354 Failure to Communicate (log only)

373 Fire Loop Trouble

374 Exit Error Alarm

380 Trouble Zone Type 5

381 RF Supervision Trouble

382 Supervision Auxiliary Wired Zone

(sent after code 333 is sent)

383 RF Sensor Tamper and Double-Balanced

Zone Tamper

384 RF Sensor Low-battery

393 Clean Me (ESL smoke detectors only)

Code Definition

401 Disarmed, Armed AWAY,

Armed MAXIMUM

403 Schedule Arm/Disarm AWAY

406 Cancel by User

407 Remote Arm/Disarm (Downloading)

408 Quick Arm AWAY

409 Keyswitch Arm/Disarm AWAY

412 Successful Download/Access

441 Disarmed/Armed STAY/INSTANT,

Quick-Arm STAY/INSTANT

442 Keyswitch Arm/Disarm STAY

461 Wrong Code Entry (keypad lockout activated)

570 Bypass

601 Manually Triggered Dialer Test

602 Periodic Dialer Test

606 Audio Alarm Verification (AAV) to Follow

607 Walk Test Entered/Exited

623 Event Log 80% Full

625 Real-Time Clock was Changed (log only)

626 Time/Date Inaccurate

627 Program Mode Entry (log only)

628 Program Mode Exit (log only)

750 -

789

Reserved for Configurable Zone Type report

codes (check with central station when using

these codes)

801 Override Tamper Arming (log only)

802 Override Low Battery Arming (log only)

803 Override AC Loss Arming (log only)

804 Override Supervision Fail Arming (log only)

999 Non-Alarm Zone Type (Zone Type 23) Fault

(log only)

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 23 24

Comments to this Manuals

No comments

Vista Ademco -10SE User's Guide Page 11

Comments to this Manuals

Related products and manuals for Security access control systems Vista Ademco -10SE