Vista Columbus Triplex User Manual Page 14
- Page / 90
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
0150-0201C 14 Vista Columbus System Triplex
1.8 Power-Up
It is important that the power-up procedures be followed carefully. The unit uses its auto-detect
feature to detect camera signals during power-up, and configure itself automatically.
Power-up procedure
Power Supply Input
Once the system installation is complete, apply
power in the following order:
1. Energize the monitors and all of the cameras.
2. Energize the Columbus System Triplex.
Voltage: 12 Volt DC
Power: 60 Watt (5 Amp)
Connector: 2.1mm barrel, centre positive
Once power is applied to the unit, it will begin its power-up procedure. The unit will begin by displaying
the software version on Monitor-A, then the unit will begin recording automatically.
Check Video Input Quality
Check the picture quality by selecting each camera for full screen display. If the picture quality is poor,
check the following items:
• The BNC connections.
• The loop-through terminations.
• The video levels of incoming signals.
• The possibility of ground loops.
• Consult the camera’s installation instructions for additional information about proper camera setup.
Check Record And Playback Quality
Record for at least three minutes at the default record rate. Then play back the recording, selecting
each camera for full screen display. Check the playback picture quality.
1.9 Minimum Recommended Menu Setup
After installation is complete, it is strongly recommended that, as a minimum, the items in the
QuickInstall menu be configured before the unit is used. All the features located in the QuickInstall
menu are also found in the Main menu. These items are provided in the separate QuickInstall menu
as a convenience for the installer.
For information about accessing and configuring the menu system, see Section 3.
To find detailed information in this manual about configuring each item in the QuickInstall menu, use
the following table to locate the main menu location of each item in the QuickInstall menu.
- User Manual 1
- Contents 3
- 1.2 Product Description 6
- 1.3 Passwords 6
- 1.4 Unpacking 7
- 1.5 Installation Environment 7
- 1.6 Associated Equipment 8
- 1.7 The Back Panel 8
- Camera Inputs 9
- Composite Monitor Output 9
- Y/C Monitor Output 9
- Alarm I/O Port 9
- Alarm Input 10
- Alarm Relay Output 11
- AUX Port 11
- 82 3 4 5 6 71 12
- 1.8 Power-Up 14
- 2.2 The Front Panel 16
- 2.3 Live Viewing 17
- 2.4 Playback 18
- 2.5 Recording 20
- 2.6 Display Options 22
- 2.7 Active Cameos 22
- 2.8 Sequencing 23
- 2.9 On-screen Indicators 24
- Status Indicators 25
- Conditional Indicators 25
- Status Display Box 25
- 2.10 Triplex Mode 26
- 2.11 The Print Image Feature 28
- 3 Menu System Overview 29
- 3.4 Menus In This Manual 30
- 3.6 Menu Shortcuts 30
- 3.7 The Main Menu 31
- 3.8 Time/Date 31
- Date Format Setup 32
- Select Format 32
- MM/DD/YY 32
- 3.9 Sequencing 33
- 3.10 Record 34
- [CANCEL] [OK] 38
- No overwrite 39
- Write once 39
- Continuous 39
- 3.11 Alarms 40
- Alarm Record Mode 41
- Interleaved 41
- Select Mode 41
- Fullscreen Alarm 42
- Fullscreen 42
- Relay Configuration 43
- Relay 01: 43
- Relay 02: N/CLOSED 43
- Email Notification Setup 44
- TCP/IP Notification Setup 44
- 3.12 Macro 45
- Macro Excluded Features 46
- 3.13 Motion Detection 47
- Enable All 48
- Disable All 48
- Individual Enable 48
- 3.14 Camera Setup 50
- Signal Gain Setup 51
- Camera 01 51
- Signal Gain 100% 51
- Power Up Disable 52
- Auto Disable Now 52
- Individual Disable 52
- 3.15 Archive Setup 53
- 3.16 Audio Setup 54
- 3.17 Telemetry 54
- Disabled 55
- 3.18 Communications 56
- POTS Setup 57
- 3.19 Front Panel Lock 58
- 3.20 Factory Settings 59
- 3.21 Passwords 59
- 3.22 The QuickInstall Menu 60
- 3.23 The Operator Menu 60
- 3.24 The SystemView Menu 61
- The View Screens 62
- View Screen 1 62
- View Screen 2 62
- View Screen 3 62
- View Screen 4 63
- View Screen 5 63
- View Screen 6 63
- View Screen 7 63
- View Screen 8 64
- 4 Alarms 65
- LIVE MODE 66
- PLAYBACK MODE 66
- 4.6 Alarm History Box 67
- 5 Searching 68
- 5.1 Disk Analysis Screen 69
- 5.2 Quick Archive to CD 69
- 5.3 Motion Search 70
- 5.4 Search Filters 71
- 5.5 Search Results 72
- 6 Telemetry Controls 73
- Using Telemetry Cameras 74
- Using presets 75
- 7 Web Interface 76
- 7.1 WaveBrowser 77
- The Main Viewing Area 78
- The Button Panel 79
- 8 Technical Specifications 80
- Motion Detection 81
- Part Numbers 81
- 9.1 Message Structure 82
- 9.2 Message Type 82
- 9.3 Event Field 82
- D – Event 0x03 83
- Remote Control Protocol 84
- 10.2 Configuration and 85
- 11 Macro Tables 86
- 11.2 Scheduled Macro Table 87
- 12 Warranty and Service 88
- 12.2 Warranty 89
- 0150-0201C 90
Related products and manuals for Digital Video Recorders (DVR) Vista Columbus Triplex
(72 pages)
(125 pages)
(16 pages)© 2020, manymanuals.com. All rights reserved. | 0.183 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals